Innokin T22 Pro Kit [Matte Black]

Product Information

This does miss an adjustable airflow control. It doesn’t need a lot of adjustment but it would be nice to tailor it to my preference a bit more. Vapers who currently use pen style devices like many in the Endura range will see this kit as a stepping stone to using more advanced kits as they become accustomed to carrying around larger mods. The Innokin Endura T22 Pro Kit is a relatively simple device to use. By following these steps, you should be able to get started vaping with it right away. Best Wholesale Vape Supplier – UPENDS As this is a MTL kit I am using my usual MTL e-liquid – 11mg Nicotine CrazySaltzzz in Bubblegum. This is a 50/50 VG/PG mixture. Make sure to prime your coil upon first use. 1 drop of e-liquid per cotton juice port is enough. Once primed, allow the coil to stand in a 3/4ths full tank for at least 15 minutes before vaping.

In fact when I first looked at it I wasn’t even sure if the base screwed off like previous versions as it looked to be all one piece – epic design and quality! Certainly, the Endura T22 Pro kit does the job very well and offers a very tight quality vapour, ideal when you start vaping, but we would have liked to find a possibility to vary the air supply to evolve in your vape. According to the periods, one can appreciate a little more volume of vapour with a seasonal liquid. Another negative point, during our tests, we noticed an accumulation of condensation under the atomizer. It is quite logical, the air circulation space is limited and targeted on an area of the atomizer. Nothing serious for as much, but it is necessary to take care, punctually, to unscrew its atomizer to dry it with a cloth or paper towel. Adjust power = press and hold the wattage selection button until the required number of LEDs are lit – see diagram below.

The air will pass through this small hole and will circulate around the resistance thread to finally rush through the hole located on it. Allow your coil to "break-in" before using it at the maximum recommended wattage level. Start your coils off at the low end of the recommended wattage range, and gradually increase to your desired wattage level slowly over the first day of using your new coil.

The Innokin Endura T22 Pro kit comes equipped with the T18E Pro tank, specifically designed for Mouth-to-Lung (MTL) vaping. This 2ml capacity tank is ideal for those who prefer a more restricted airflow and a focus on flavor. The tank features a convenient sliding top-fill mechanism, allowing for effortless refills on the go. This design ensures a cleaner and more efficient filling process, eliminating the need for complicated disassembly. As the manual does not specify the colour of the LED on the fire button according to battery charge remaining I have had to figure this out myself – see the battery life section for a guide. Although the 1.5ohm is still a good coil – I think the kit should just focus on the other two coils and leave the 1.5ohm behind. For a new coil or first time use leave it to stand for 10 minutes for the coil to absorb the e-liquid. Even though we have a lot of great starter pod kits on the market now – for simplicity and performance I still recommend the Endura range to people who want a faff free vape to get them off the ciggies.Another great thing about the Zlide Top Tank is it is leakproof and features a genius vape juice reservoir, which makes coil changing a breeze. The tank is also compatible with Innokin Z Coils, which are available in a range of MTL and RDL configurations. It features a large 3000mAh battery, handy USB-C charging and provides a tight mouth-to-lung style draw. Please start with low wattage/temperature and increase it slowly&steadily through up the range until you find the favorite flavor of your e-liquid. It might not be as cheap as other kits, but it should still fit within many vapers budgets, and with the pedigree Innokin commands, you can be confident that it will last.

The Innobar C1 is the perfect alternative to the Endura S1 if you find e-liquid refilling messy and cumbersome. The C1’s pods are already pre-filled, with 16 flavours to choose from. What makes it stand out is it doesn’t use regular PG/VG vape juice, and instead uses water-based e-liquid! Water-based e-liquids deliver smoother vapour and faster satisfaction compared to normal e-liquids, so it’s worth trying if you find traditional vapes a little harsh. Paired with an advanced 1.1ohm mesh coil and 3.6V constant output, you’ll get to enjoy smooth and unmatched flavour with every puff. Breaking this down I got 15 hours vaping until the LED changed from Green to Orange (yes 15 hours!!!) For standard,high resistance atomizers or restrictive devices (ex. pod based,pen), we recommend 6mg or higher due to the mouth to lung (MTL) design of this atomizer,tank. Preference may vary depending on the user and frequency of use.It is worth noting you really need to keep on top of the e-liquid level – anything below approximately 1/4 full will likely result in burning out the coil. Innovative product designs: UPENDS is constantly innovating and coming up with new and improved vaping products. Their products are known for their sleek, stylish designs, as well as their user-friendly functionality. If your battery does charge properly in one charger but does not charge properly in another, your charger is faulty, not your battery. The unit’s base includes four rubber nodes to protect the bottom from scuffs and lower the noise made when placing the device on a hard surface. Believe me; your furnishings will thank you! If you’ve tried the tips above and your battery is not charging properly, you have a faulty battery.

windows surround the outside of the tank giving a clear view of the liquid level and it is that clear a view you can even see the coil resistance!

I do think this is old coil technology compared to the newer 1.7ohm coil – it is the weaker of the 2 coils included. If you are looking for a wholesale vape supplier that can provide you with high-quality products, innovative designs, and exceptional customer support, then UPENDS is a great option. This despite looking like it is made from metal actually lights up in green, red or yellow depending on the battery charge remaining.