Waveshare Ethernet Module, High-Performance 10/100 Ethernet Physical Layer Transceiver (PHY)

Product Information

Installing using the ZIP file and then updating using the Library Manager will result in duplicate libraries. For using the thermostat function, publication of the measured temperature was using the wrong name. Changed to the common used name.

emac: Timed out waiting for PHY register 0x2 to have value 0x0007 (mask 0xffff). Current value 0xffff emac: Timed out waiting for PHY register 0x3 to have value 0xc0f0 (mask 0xfff0). Current value 0xffff Go grab your Raspberry Pi Pico board and a micro USB cable. Plug the cable into your Raspberry Pi or laptop, then press and hold the BOOTSEL button on your Pico while you plug the other end of the micro USB cable into the board. Then release the button after the board is plugged in. A better choice seems to be the LAN8720 which costs only 1EUR and is significantly smaller as it only has a RMII-interface an therefore lesser pins. iBeacon (xdrv_52): Clean up BLE_ESP32 based driver; add commands and advert timing. Remove HM10 code - it's in the other one..... my knowledge is not so deep to understand if Olimex has more feature than the proposed cheaper deviceUnfortunately the most common (and cheapest) breakout for the LAN8720 isn’t breadboard-friendly, although you can find some boards that are, so you’ll probably need to grab a bunch of male-to-female jumper wires along with your breadboard. LAN8720 breakout wired to a Raspberry Pi Pico on a breadboard (with reset button) Zibee add ``SetOption120 1`` or ``ZbEndpointTopic`` to add the endpoint as suffix in topic when using ``SetOption89 1``

I have successfully flashed WT32-ETH01 using FT232RL FTDU module, ESP_Flasher and tasmota32-ethernet.bin (from https://github.com/tasmota/install/raw/main/firmware/unofficial/tasmota32-ethernet.bin) I made a small prototype for the eBox ESP32-T and the Waveshare LAN8720 ETH Board which already has an 50MHz oscillator. When STM become officially supports external PHY Ethernet, I will delete this repository. Hardware requirements it would be great to connect for example some relay for domotic usage and having it cable by lan instead of wifi only Add commands ``ZbNameKey``, ``ZbDeviceTopic``, ``ZbNoPrefix``, ``ZbEndpointSuffix``, ``ZbNoAutoBind``, ``ZbNameTopic`` as synonyms for ``SetOption83, 89, 100, 101, 110 and 112`` respectively

Parametrics

Remove the two jumpers from CN2, and place them at the two outermost empty jumper pins marked CN11 and CN12. the advantage could be that if wifi is not good we can use lan cable, maybe it could be PoE powering?

Add commands ``ChannelRemap``, ``MultiPWM``, ``AlexaCTRange``, ``PowerOnFade``, ``PWMCT``, ``WhiteBlend``, ``VirtualCT`` as synonyms for ``SetOption37, 68, 82, 91, 92, 105 and 106`` respectively

10/100 Base-T/TX Ethernet Transceiver with MII/RMII Interface

TheLAN8720A/LAN8720Ai connect via an RMII interface.These devices support HP Auto-MDIX†, employ Microchip's proprietary flexPWR ® technology andare available in both extended commercial (0°C to 85°C) and industrial (-40°C to 85°C) temperature range options.

Power and mode must be individually controllable. Some devices may not function properly if the mode is also turned off when the power is turned off. BUT when I turn wifi off (wifi 0 in console or changing wifi configuration to non existing wifi), I also loose Ethernet connection. Raspberry Pi Pico has a lot of interesting and unique features, but it doesn’t have networking. Of course this was only ever going to be a temporary inconvenience, and sure enough, over Pi Day weekend we saw both USB Ethernet and Ethernet PHY support released for Pico and RP2040. Raspberry Pi Pico and RMII Ethernet PHY BLE_ESP32 (xdrv_79): Start scan as soon as we are connected to a device - saves missing a few adverts.Actually the board has two STM32 chips. One is the target of the demo board, and the other is the STLINK. EMAC_TXD0, EMAC_TXD1, EMAC_TX_EN, EMAC_RXD0, EMAC_RXD1, EMAC_RX_DV and EMAC_TX_CLK are fixed and can't be rerouted to other GPIOs. EDIT: After reading that the lenght of wires can be an issue at 50MHz, I wired it with 10cm wires (instead of 20cm on the photo), still the same. If everything goes well you should have a UF2 file in build/examples/httpdcalled pico_rmii_ethernet_httpd.uf2. You can now load this UF2 file onto your Pico in the normal way. The LAN8710A/LAN8710Ai connect to the MAC layer using a variable voltage, digital standard MII or RMII interface,These devices support HP Auto-MDIX†, employ Microchip's proprietary flexPWR ® technology andare available in both extended commercial (0°C to 85°C) and industrial (-40°C to 85°C) temperature range options.